-
WLAN active/inactive
Activates/deactivates wireless LAN.
-
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note-
You can enter this setting menu by following the procedure below:
1. Select Setup on the HOME screen.
2. Select Wireless LAN setup.
In this case, activate wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the machine detects the access point, follow the on-screen instructions to set up wireless LAN. If an access point is not detected or if you select another setup method, select one of the setup methods below.
-
Standard setup
Select when you perform settings for wireless LAN manually using the operation panel of the machine.
-
WPS
Select when you perform settings for wireless LAN using Wi-Fi Protected Setup (WPS). Select Push button method or PIN code method according to the method your access point supports, then follow the on-screen instructions.
-
Other setup
Select WCN or Advanced setup. If you select WCN, you need a USB flash drive on which settings for wireless LAN are saved. If you select Advanced setup, follow the on-screen instructions.
-
-
Confirm LAN settings
The list of wireless LAN settings of this machine is displayed on the LCD. You can print the list from this setting menu.
-
WLAN setting list
The list of wireless LAN settings of this machine is displayed on the LCD.
The following setting items are displayed.
Items
Setting (IPv4)
Setting (IPv6)
Connection
Active/Inactive
Active/Inactive
SSID
XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXCommunication mode
Infrastructure
Infrastructure
Channel
XX
XX
Wireless LAN security
Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)
Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)
IP address
XXX. XXX. XXX. XXX
XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXSubnet mask
XXX. XXX. XXX. XXX
-
Subnet prefix length
-
XXX
Default gateway
XXX. XXX. XXX. XXX
XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC address
XX:XX:XX:XX:XX:XX
XX:XX:XX:XX:XX:XX
IPsec settings
-
Enable (ESP)/Enable (ESP & AH)/Enable (AH)/Disable
Pre-shared key
-
XXXXXXXXXXXXXXXX
Printer name
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
Bonjour service name
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX("X" represents an alphanumeric character ranging from 0 to 9 and A to F.)
-
Print LAN details
You can print out the network settings of the machine such as its IP address and SSID.
For more information on the machine's network setting is printed out:
Printing Out Network Setting Information
Important-
This printout contains valuable information about your computer. Handle it with care.
-
-
-
Other settings
-
Set printer name
Specifies the printer name. You can use up to 15 characters for the name.
Note-
You cannot change this setting with the memory card inserted in the card slot.
-
You cannot use the same printer name as that already used for other LAN connected devices.
-
You cannot use a hyphen for the initial or last character of the printer name.
-
-
TCP/IP settings
Selects the IP version (IPv4 or IPv6). Be sure to select IPv4.
-
Set memory card sharing
Selects whether to share the card slot with a LAN connected computer.
Note-
You cannot change this setting with the memory card inserted in the card slot.
-
-
WSD setting
Setting items when you use WSD (one of the network protocols supported in Windows 7 and Windows Vista).
- Enable/disable WSD
-
Selects whether WSD is enabled or disabled.
-
When this setting is activated, the printer icon is displayed on the Network Explorer in Windows 7 and Windows Vista.
- WSD scan from this device
-
Selecting Enable allows you to transfer the scanned data to the computer using WSD.
- Timeout setting
-
Specifies the timeout length.
Note -
Bonjour settings
Setting items for LAN using Bonjour for Macintosh.
- Enable/disable Bonjour
-
Selecting Enable allows you to use Bonjour to perform the network settings.
- Service name
-
Specifies the Bonjour service name. You can use up to 48 characters for the name.
Note-
You cannot use the same service name as that already used for other LAN connected devices.
-
LPR protocol setting
Activates/deactivates the LPR setting.
-
-
Reset LAN settings
Initializes the network settings on the machine.
Important-
Note that initialization erases all connection settings with computers, and printing or scanning operation may become impossible. To use the machine over network, perform setup with the Setup CD-ROM. Be careful when you initialize the network settings on the machine.
Note-
When you initialize the network settings using IJ Network Tool:
-
